Currently, we run sv start immediately after linking the service.
The runsv process may not be up at the moment, as a result of which
openrc will mark the service as stopped, even though it may be brought up
by runit at the next scan.
This is documented in the gentoo wiki:
https://wiki.gentoo.org/wiki/Runit#OpenRC.27s_runit_integration_feature
This PR adds a timeout so that correct process state can be reported.
Before:
* Starting netdata-runit ...
fail: /run/openrc/sv/netdata: runsv not running
* Failed to start netdata-runit
After:
* Starting netdata-runit ...
fail: /run/openrc/sv/netdata: runsv not running
ok: run: /run/openrc/sv/netdata: (pid 9042) 0s
This fixes#253.
Fix the following error:
broadcast.c:41:21: error: '__UT_LINESIZE' undeclared (first use in this function); did you mean 'UT_LINESIZE'?
#define UT_LINESIZE __UT_LINESIZE
^~~~~~~~~~
Constant UT_LINESIZE is defined in <utmp.h> provided by musl.
Busybox timeout does not support the `-k` flag. As such, invoking fuser
from do_unmount never worked without this patch. This went unnoticed as
standard error is redirected to /dev/null. This patch fixes this by
simply removing the incompatible `-k` flag.
[Ariadne: the `-k` is redundant anyway, since we are sending the KILL
signal to begin with.]
Since musl 1.2 time_t is a 64 bit value, even on 32 bit systems. A
hotfix for printing the value is simply using PRIu64 from inttypes.h
in the format string.
This fixes#446.
supervise-daemon was apparently overlooked when support for the
SSD_IONICELEVEL environment variable was added. This commit brings
supervise-daemon up to parity with start-stop-daemon with respect to
this environment variable.
Newer devices have multiple power_supply devices in sysfs:
$ grep ^ /sys/class/power_supply/*/type
/sys/class/power_supply/AC/type:Mains
/sys/class/power_supply/BAT0/type:Battery
/sys/class/power_supply/ucsi-source-psy-USBC000:001/type:USB
/sys/class/power_supply/ucsi-source-psy-USBC000:002/type:USB
There are two "USB" Type-C ports than can supply power and both are
aggregated into the "Mains" power supply by the firmware. The "Battery"
also counts as a power supply, but is missing the online attribute.
The -f check with a wildcard pattern results in an error, when multiple
devices are present:
/lib/rc/bin/on_ac_power: line 21: [: too many arguments
When the power_supply class is registered, check for a "Mains" device.
Fixes#427.
Since commit 6b475ab269, openrc tries to load
modules twice which have been defined in /etc/conf.d/modules via modules=
variable when /bin/sh points to dash shell.
The reason is that when the "modules-load" service was merged into "modules"
service, the "modules" variable name got used in both, load_modules()
function and in Linux_modules() function which both get called when modules
service is started. Although "modules" variable is marked as local in
load_modules(), dash simply ignores this.
Avoid the issue by renaming "modules" variable to "_modules" in
load_modules() function.
This fixes#419.
In legacy cgroups mode, we were running `mountinfo -q ""` which was
generating an error message. If we return immediately when
cgroup2_find_path returns an empty value, we avoid this message.
The previous fix excludes PIDs of processes running in a different namespace
regardless of whether the PID has been explicitly stored in a PID file mentioned
in the --pidfile parameter. The correct behavior is to only exclude the pid if
it is not stored in a pidfile.
X-Gentoo-Bug: 776010
X-Gentoo-Bug-URL: https://bugs.gentoo.org/776010
The cgroups v2 setup required the rc_cgroups_controllers variable
to be set to the list of controllers to enable regardless of whether the
mode was hybrid or unified.
This makes sense for hybrid mode since the controllers can't be in both
the cgroups v1 and v2 hierarchies, but for unified mode we should enable
all controllers that are configured in the kernel.
The test `[ -h "${ifname}" ] && continue` skips the symlinks while it is
the opposite that is the expected: ignoring files that are not symlinks.
Fixes commit f42ec82f21.
This fixes#391.
Otherwise this would create the following output:
rc-status -f ini
* Caching service dependencies ... [ ok ]
[default]
dbus = started
NetworkManager = started
syslog-ng = started
...
This fixes#364.
I found the original note a little confusing, since using rc-update will
add it to a runlevel so it *is* auto-started when the system reaches
that runlevel again, but I don't think that was the intended meaning of
'auto-start', so hopefully this makes it a little more clear.
Currently when osclock is enabled as a init.d service the following
messages appear during boot when osclock starts:
* The command variable is undefined.
* There is nothing for osclock to start.
* If this is what you intend, please write a start function.
* This will become a failure in a future release.
osclock is activated whenever a machine's system clock is automatically
configured from a RTC by the kernel and the osclock's only purpose is to
satisfy the "clock" dependency defined by other init.d services.
Adding a stub start() function prevents OpenRC from showing warnings but
continues to ensure that the osclock service still does not actually do
anything.
This fixes#377.
The do_check() function recently gained some defenses against symlink
replacement attacks that involve the use of *at functions in place of
their vanilla counterparts; openat() instead of open(), for example.
One opportunity to replace mkdir() with mkdirat() was missed, however,
and this commit replaces it.
This fixes#386.
start-stop-daemon and supervise-daemon parse usernames and group names
passed via the --user argument as numeric UID/GID if they start with a
number (e.g. user "4foo" will be treated as UID 4). This results in the
process that is being started to run under a totally unexpected user if
that UID exists.
Even though the result of the sscanf calls are tested for a result of
exactly 1, which means exactly one value was extracted, because sscanf's
format string only contains only one placeholder, it will never return
a value greater than 1, even if there are still characters left to be
parsed. This causes start-stop-daemon and supervise-daemon to assume
that usernames starting with a number are just that number. Adding a
second placeholder "%1s" to the format string, which matches a string of
length 1, makes sure that sscanf can distinguish between pure numbers
(in which case it will return 1) and strings either starting with a
number (in which case it will return 2) and any other string (in which
case it will return 0).
This fixes#379.
This fixes#380.
Starting program: /sbin/start-stop-daemon --start --exec i-dont-exist
Program received signal SIGSEGV, Segmentation fault.
0x0000555555559053 in main (argc=1, argv=0x7fffffffdc20)
at start-stop-daemon.c:631
631 *exec_file ? exec_file : exec);
This fixes#385.
This walks the directory path to the file we are going to manipulate to make
sure that when we create the file and change the ownership and permissions
we are working on the same file.
Also, all non-terminal symbolic links must be owned by root. This will
keep a non-root user from making a symbolic link as described in the
bug. If root creates the symbolic link, it is assumed to be trusted.
On non-linux platforms, we no longer follow non-terminal symbolic links
by default. If you need to do that, add the -s option on the checkpath
command line, but keep in mind that this is not secure.
This fixes#201.
When executable is provided just by name (and therefore searched in a
path), exec_file is reset to NULL every time. exists() handles it being
NULL just fine, but dereferencing it in eerror does not work.
Fixes#326Fixes#327
It looks like some stray text was left at the bottom of the file:
```
package.
migrating your system to openrc-init.
```
There's a subsection on migrating a system to `openrc-ini`; perhaps this was
an embryonic section title?
This fixes#347.
prior to cgroups getting mounted, /sys/fs/cgroup will still exist,
but attempts to make directories in it will fail, change cgroup2_set_limits() to
verify that cgroups are mounted instead of just checking that /sys/fs/cgroup
exists.
This fixes#307.
This fixes#321.
This allows openrc to direct sysvinit to shut down the system by setting
the INIT_HALT environment variable appropriately. Also, we do not try to
communicate with sysvinit if its fifo does not exist.
I am removing this on the advice of a member of the Gentoo toolchain
team. It was explained to me that this doesn't offer any significant
benefits to OpenRC.
If anyone ffeels differently, please open a pull request reverting
this and adding an explanation of what it does and how to know which
functions to mark hidden in the future.
This fixes#301.
The do_openrc() function was not waiting properly for the child process
which started the runlevel to return. We need to repeatedly call
waitpid() until its return value matches the pid of the child process or
the child process does not exist.
This fixes#216.
This fixes#300.
The 'readelf'-based tests cover a few situations:
1. undefined symbols in shared libraries
2. unexpected exports in shared libraries
Bug #575958 shows that [2.] implementation is too simplistic
in assuming that presence of relocation equals to export presence.
It is incorrect for PLT stubs and local symbols.
Let's just drop these tests.
If one needs to cover [1.] it is better to use LDFLAGS=-Wl,--no-undefined.
This closes#292.
X-Reported-by: Benda Xu
X-Gentoo-Bug: https://bugs.gentoo.org/575958
X-Gentoo-Bug-URL: https://bugs.gentoo.org/575958
The -f option can be used when showing the status of services in
runlevels to allow making the output more easily parsable.
Currently, the .ini format is the only one supported.
The .Dt header is supposed to be all caps. This was mixing case.
The options block was being incorrectly indented due to a missing .El.
Some of the new options were missing the .It block, so add that.
Finally, the -D option was missing capitalization.
readlink(3) does not nul-terminate the result it sticks
into the supplied buffer. Consequently, the code
rc = readlink(path, buf, sizeof(buf));
does not necessarily produce a C string.
The code in rc_find_pid() produces some C strings this way
and passes them to strlen() and strcmp(), which can lead
to an out-of-bounds read.
In this case, since the code already takes care to
zero-initialize the buffers before passing them
to readlink(3), only allow sizeof(buf)-1 bytes to
be returned.
(While fixing this issue, I fixed two other locations that
used the same problematic pattern.)
This fixes#270.
The contents of /proc/<pid>/cmdline are read into
a stack buffer using
bytes = read(fd, buffer, sizeof(buffer));
followed by appending a null terminator to the buffer with
buffer[bytes] = '\0';
If bytes == sizeof(buffer), then this write is out-of-bounds.
Refactor the code to use rc_getfile instead, since PATH_MAX
is not the maximum size of /proc/<pid>/cmdline. (I hit this
issue in practice while compiling Linux; it tripped the
stack-smashing protector.)
This is roughly the same buffer overflow condition
that was fixed by commit 0ddee9b7d2
This fixes#269.
The following will cause a segfault due to NULL being
passed to strcmp(3)
$ RC_SVCNAME=foo supervise-daemon
Fix the bounds check on argc in main. If argc<=1, then
it is not safe to dereference argv[1].
The statement
ll = strlen(applet);
appears twice in the same block without any
intervening assignment to the variables
'll' or 'applet'
Remove the second (duplicate) statement.
We have used /run for some time now and we have had this migration
script for 6 years. Linux users should have upgraded by now to a version
of OpenRC which stores its information in /run.
In order to run healthcheck() and the unhealthy() function, add an
exec_command call to the supervisor.
Another difference is This function also logs errors instead of
attempting to display them.
This is for #271.
I do not know of a need to have the default shell be a build-time
configurable setting. All *nix systems I am aware of have /bin/sh as a
default posix compatible shell.
If some systems running OpenRC do not make that assumption about
/bin/sh, I will consider bringing this back, so feel free to open an
issue.
Without a respawn period setting, the supervisor will give up on
respawning agetty after it is respawned respawn_max times. For most
daemons giving up like this is reasonable, but not for agettys. Agettys
should always be respawned unless they are respawning too fafst,.
If an agetty is respawning faster than 10 times in 60 seconds, this
seems to be too fast.
Since the pid file is internal to us, start moving toward deprecating it
by not requiring the user to specify it.
In the next release, I plan on working on code to start phasing out the
use of a pid file if this is possible.
This is needed in preparation for adding support for a fifo to allow us
to communicate with the supervisor to ask it to signal the child it is
supervising.
This reverts commit 2af0cedd59.
After speaking with Luis Ressel on the Gentoo selinux team, I am reverting
this commit for the following reasons:
- Luis told me that he feels this is not the solution we need to address
the concern with checkpath; I will be working with him on another
solution.
- There are concerns about the way the path variable was handled
and the assert() call.
The path variable should be dynamically allocated using xasprintf
instead of defining a length at compile time. This would eliminate the
need for the assert() call.
- It introduces the definition of _GNU_SOURCE which makes it
easier to introduce portability concerns in the future (see #262).
The pidfile of the supervisor doesn't need to be adjustable by the
service script. It is only used so the supervisor can stop itself when
the --stop option is used.
In start-stop-daemon and rc-schedules, we were printing out a warning if
the nanosleep call was interrupted by a signal, but we did not treat
this as an error situation other than displaying the message, so there
is no need for the message.
These services represent the parts of the keymaps and termencoding
services which saved the settings back to the root file system so they
can be loaded very early in the boot process.
These are needed to allow keymaps and termencoding to run earlier in the
boot sequence.
X-Gentoo-Bug: 446018
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=446018
On Linux, kernel modules should be loaded once during boot, either in an
initramfs or by this service.
This does not change anything other than printing out messages if a
module is loaded more than once.
X-Gentoo-Bug: 659530
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=659530
Health checks are a way to monitor a service and make sure it stays
healthy.
If a service is not healthy, it will be automatically restarted after
running the unhealthy() function to clean up.
You can now schedule a shutdown for a certain time or a cpecific number
of minutes into the future.
When a shutdown is running, you can now cancel it with ^c from the
keyboard or by running "openrc-shutdown -c" from another shell.
Fix the comparison between respawn_count and respawn_max so that
respawn_max = 1 will allow for one respawn. Since respawn_count is
incremented before the comparison, use a 'greater than' comparison
so that respawn will be triggered when respawn_count is equal to
respawn_max.
Fixes: https://github.com/OpenRC/openrc/issues/247
Fixes: https://github.com/OpenRC/openrc/issues/248
We do not need to do this any longer since all supported linux kernels
make efivarfs immutable and the tools that manipulate it are aware of
this feature.
This fixes https://github.com/openrc/openrc/issues/238.
Use errno != EACCES to fix false-positive for non-root users
with grsecurity kernels.
Fixes: 37e2944272 ("librc: Add check for crashed state")
This fixes#237
This test to find if we could see pid 1 was being used inconsistently in
rc-status and mark_service_crashed to decide whether we could test to
see if the daemon for the service was crashed, and it was not part of
the librc library.
I am removing it from the executables because of inconsistent usage. I
will add it to the library if it is needed there.
Gentoo was changing some of our installation modes from 0444 to 0644.
There isn't a reason to install things 0444, so we are switching these
to 0644 so the Gentoo ebuild doesn't need this extra step.
This removes localmount from the dependencies of the consolefont,
keymaps, numlock and procfs services.
These services are Linux only and the default modern linux system has /
and /usr on the same file system.
This also fixes the following issue.
X-Gentoo-Bug: 651998
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=651998
If pidfile does not exist when we are stopping the daemon, assume it is
already stopped, and report success.
hostapd is an example of a daemon which removes its pidfile when it is
exiting. If this daemon terminates prematurely, that is, without s-s-d
involvement, then openrc fails to restart it, because s-s-d "stop"
command fails when pidfile is missing.
X-Gentoo-Bug: 646274
X-Gentoo-Bug-URL: https://bugs.gentoo.org/646274
The current check only tries to detect whether /sys/fs/cgroup exists and
whether it is writable or not. But when the init system doesn't mount
cgroups then /sys/fs/cgroup will just be an empty directory. When paired
with unprivileged containers that mount sysfs this will cause misleading
errors to be printed since /sys/fs/cgroup will be owned by user
nobody:nogroup in this case. Independent of this specific problem this
check will also be misleading when the /sys/fs/cgroup exists and is in
fact writable by the init system but isn't actually a mountpoint.
Note from William. "grep -qs" doesn't need to redirect output to
/dev/null since it is completely silent.
This fixes#209.
This is our own version of asprintf(). This original code was written by
Mike Frysinger, and I was able to modify it to use our memory helper
functions.
We need a version of this code because it is not available on glibc at
least without defining _GNU_SOURCE, and I would rather not do that.
This is the first step in improving string handling in OpenRC for #207.
The "Ar" tag for the mountinfo command contained a typo (leading
space) that resulted in the tag being output verbatim; that is,
mountinfo ... .Ar mount1 mount2
rather than e.g.
mountinfo ... <mount1> <mount2>
This commit deletes the leading space to fix the output.
This fixes#204.
The BUILTINS are all surrounded by Xo...Xc tags, but the opening "Xo"
was missing from the two commands fstabinfo and mountinfo. This commit
adds them, and thereby fixes the spacing when viewed by man.
This is for #204.
Refer to /var/run in the documentation instead of /run, and make it
clear at the top of the pidfile section that we use /run under Linux.
This is for #202.
This is related to #195.
This is an attempt to shorten the window for the first two issues
discussed by using a file descriptor which does not follow symbolic
links and using the fchmod and fchown calls instead of chown and chmod.
with.
rc_deptree_update_needed would return early as soon as it found
any file newer than the existing dependency cache. Unfortunately,
the first file found may not be the newest one there; so the
clock skew workaround in rc-misc:_rc_deptree_load would be given
a timestamp that was still too old.
This fix forces a full scan of all relevant files, so as to
ensure that we return a timestamp that will allow the clock skew
fix to operate. The runtime cost is no worse than the case where
the cache is up to date (ie. we must check every possible file).
This fixes#161.
Add the following variables to expose more arguments that can be passed
to start-stop-daemon or supervise-daemon:
- directory will be passed to --chdir
- error_log will be passed to --stderr
- output_log will be passed to --stdout
- umask will be passed to umask
This is for #184.
Add the ability to force-kill a service if it does not go down
successfully. Also, adjust the default wait time for an s6 service to go
down to 60 seconds.
The OpenRC team does not currently know of any modern linux tools that
require /etc/mtab to be a flat file, so this puts users on notice that
the mtab service will be removed in the future.
localmount had mtab in its "use" dependencies; however, it makes more
sense to add "before localmount" to the mtab service and remove
"use mtab" from the localmount service.
Ignore namespaces if there are errors reading either the pid namespace
for the current process or the process we aare testing.
This fixes https://github.com/openrc/openrc/issues/180.
This is to be used if the service is being supervised and the
supervisor is somehow killed.
Currently, this is very linux specific, but I will expand to other
platforms, patches are welcome.
- Harden against dying by handling all signals that would terminate the
program and adding --reexec support
- factor the supervisor into its own function
- fix test for whether we are already running
Prior to this change, we were logging unexpected terminations of daemons
we were supervising at the info level. This change moves the logs to
warnings.
The sysfs init script referred to @LIBEXECDIR@ before this change, but
it is better to refer to RC_LIBEXECDIR so that we get rid of a sed
substitution.
The service binary was just a synonym for rc-service, so use rc-service
instead of service. If you want a "service" binary, it should be
something that can determine which service manager you are running and
run the appropriate service manager commands.
rc-selinux.c: In function ‘selinux_setup’:
rc-selinux.c:361:9: warning: assignment discards ‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
curr_t = context_type_get(curr_con);
^
Instead of looping and sending multiple signals to child processes in
cgroup_cleanup, we send sigterm followed by sleeping one second then
sigkill.
This brings us more in line with systemd's "control group" killmode
setting.
Also, this commit includes several shellcheck cleanups.
The --retry option for supervise-daemon defines how the supervisor will
attempt to stop the child process it is monitoring. It is defined when
the supervisor is started since stopping the supervisor just sends a
signal to the active supervisor.
This fixes#160.
This makes the halt wrapper sysvinit compatible. It ignores several
command line switches which are not currently implemented; however,
those can be implemented if we need to do so.
This fixes https://github.com/openrc/openrc/issues/146.
The syntax for expanding a variable with a default value is
${parameter:-word}
not
${parameter-word}
although the latter still works for a reason I could not explain.
This fixes#143.
Sysvinit shutdown has a default of single user mode, but openrc-shutdown
makes you choose a default action. Because of this, the shutdown wrapper
needs to pass --single to openrc-shutdown.
How to reproduce 1-byte overflow:
```
$ FEATURES=-test CFLAGS="-fsanitize=address -O0 -ggdb3" emerge -1 openrc
=================================================================
==1==ERROR: AddressSanitizer: stack-buffer-overflow on address 0x7fff0efd8710
at pc 0x000000402076 bp 0x7fff0efd7d50 sp 0x7fff0efd7d40
WRITE of size 1 at 0x7fff0efd8710 thread T0
#0 0x402075 (/sbin/openrc-init+0x402075)
#1 0x3cf6e2070f in __libc_start_main (/lib64/libc.so.6+0x3cf6e2070f)
#2 0x4013b8 (/sbin/openrc-init+0x4013b8)
Address 0x7fff0efd8710 is located in stack of thread T0 at offset 2432 in frame
#0 0x401cfb (/sbin/openrc-init+0x401cfb)
This frame has 3 object(s):
[32, 160) 'signals'
[192, 344) 'sa'
[384, 2432) 'buf' <== Memory access at offset 2432 overflows this variable
HINT: this may be a false positive if your program uses some custom stack unwind mechanism or swapcontext
(longjmp and C++ exceptions *are* supported)
SUMMARY: AddressSanitizer: stack-buffer-overflow ??:0 ??
```
The problem here is in the code handling reads from 'init.ctl':
```
int main(int argc, char **argv) {
...
char buf[2048];
for (;;) {
/* This will block until a command is sent down the pipe... */
fifo = fopen(RC_INIT_FIFO, "r");
count = fread(buf, 1, 2048, fifo);
buf[count] = 0;
...
}
```
`buf[count] = 0;` writes outside the buffer when `fread()` returns non-truncated read.
This fixes#138.
rc-status now shows the amount of time a supervised daemon has been
active as well as the number of times it has been respawned during the
current respawn period.
This creates --respawn-delay, --respawn-max and --respawn-period. It was
suggested that it would be easier to follow if the options were
separated.
This is for #126.
Allow limiting the number of times supervise-daemon will attempt to respawn a
daemon once it has died to prevent infinite respawning. Also, set a
reasonable default limit (10 times in a 5 second period).
This is for issue #126.
openrc-init.c and openrc-shutdown.c are based on code which was written by
James Hammons <jlhamm@acm.org>, so I would like to publically
thank him for his work.
We do not need to care about the path on the shebang line of a service
script as long as the shebang line ends with "openrc-run".
This fixes#119 and #120.
The clock services had a very long list of "before" dependencies that
referred to other services within OpenRC. For ease of maintenance,
convert these to "after clock" dependencies in the individual services.
Using wildcards in dependencies causes issues when rc_parallel is set to
yes because it can lead to deadlocks.
All dependencies need to be explicit rather than implicit.
This is the first stage of moving this direction.
Since we check for /sys/firmware/efi/efivars, we do not need to check
for /sys/firmware/efi
Since Failing to mount efivarfs is not critical, we silence the error
message from mount.
My understanding is that the kernel can autoload this module. If it
doesn't, the module should be built in or loaded from an initramfs.
This fixes https://github.com/openrc/openrc/pulls/112.
- switch from attempting to ping the default gateway to a host outside
the local network, defaulting to google.com.
- along with this, change the name of the variable that requests a ping
test to include_ping_test so the meaning is more clear.
These files have been in the distribution for some time but haven't been
installed. They are good examples of how to do things, so we should
install them.
Since deptree2dot and the perl requirement are completely optional, we
can move this tool to the support folder. This gives the user the option
of using it if they have perl installed, and means we do not have an
optional runtime dependency on perl.
Documentation for this tool has also been added to the support folder.
X-Gentoo-Bug: 600742
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=600742
The test environment previously used the system default paths instead of installing the necessary $PATH environment
variable to make finding eval_ecolors work.
This closes#117.
X-Gentoo-Bug: 374191.
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=374191.
This path should not be hard coded in the open call.
Linux prior to 2.4.19 did not have /proc/self/mounts, so for now I'm
making this value /proc/mounts everywhere, but that may change to
/proc/self/mounts on linux; I'm not sure we should care about <2.4.19.
X-Gentoo-Bug: 604646
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=604646
Now that we respect the module blacklists, don't print every module we
try to load, because it might not end up loaded due to the blacklist,
and modprobe doesn't consider that a failure.
Supervisor setups break easily when start/stop/status functions are not
default.
Applications that write multiple PIDs to a pidfile (eg HAProxy as
described in bug 601540), can also benefit from being able to call the
default start/stop/status with modified environment variables.
Expose the default start/stop/status functions as
default_start/stop/status, and use them for the defaults
start/stop/status.
Trivial usage example:
```
stop()
{
t=$(mktemp)
for pid in $(cat $pidfile) ; do
echo $pid >$t
pidfile=$t default_stop
done
rm -f $t
}
```
X-Gentoo-Bug: 601540
X-Gentoo-Bug-URL: https://bugs.gentoo.org/601540
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
The /etc/init.d/localmount script has a syntax error that causes it to
attempt to mount remote filesystems, causing the boot to fail. The
script appends a "no" to each remote filesystem type, but it should only
be append the "no" to the beginning of the list. This patch fixes
localmount on FreeBSD 12.0. A review of the mount(8) manpage on Ubuntu
12.04 suggests that this patch is correct for Linux, too.
The documentation implied that if you stop a daemon we handle multiple
pids in a pid file. This is not correct. We only handle the first pid.
X-Gentoo-Bug: https://bugs.gentoo.org/show_bug.cgi?id=601540
Busybox does not support the 'scope' argument on 'ip address add' or 'ip
route add', this is documented in BUSYBOX.md, but is no longer actually
needed, as the kernel does get it right without manual specification,
and the ifconfig variant already relies on the kernel to get it right.
This is part of #103.
X-Gentoo-Bug: 487208
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=487208
Separate loading the module, if it isn't built in or loaded, from
mounting the file system.
This also makes sure the warning about configuring the module in
/etc/conf.d/modules or building it in is displayed only if it is loaded
successfully.
X-Gentoo-Bug: 595836
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=595836
This allows us to avoid the warnings from bash-4.4 about null bytes in
command substitutions.
If you have separate /usr, are not using an initramfs, and have a file
called /proc/self/environ on your root file system, this will break.
X-Gentoo-Bug: 594534
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=594534
This reverts commit 8b4fc05ff2.
The original commit did not explain why this feature was disabled, and I
now have a request to enable it.
This fixes#24.
The $RC_UNAME "Linux" had been misspelled as "linux".
As a consequence, entries in e.g. /etc/modules-load.d failed to
load any module succesfully under Linux(!)
In the hwclock, procfs and sysfs service scripts, we automatically
attempt to load the kernel modules we need before we take any action. We
shouldn't do this, because there are systems which do not use kernel
modules and do not have the kmod package installed.
With this change, we continue to load the modules ourselves, but we warn
the admin that they need to be added to /etc/conf.d/modules or built
into the kernel.
In the future, this automatic loading will be dropped.
X-Gentoo-Bug: 342313
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=342313
The original auto detection of Docker containers assumed the presence of
a container environment variable. However, Docker-1.12 does not
implement this, and I'm not sure which versions of docker implemented
it.
The new test is for the presence of a file named .dockerenv in the
root directory.
btrfs support is not implemented yet (for q Q v), but at least tmpfiles.sh
no longer chokes about tmpfiles.d lines of recent systemd versions
This fixes#87.
We had separate sysctl scripts for each operating system. However, there
is no need to do this since we can detect the operating system at
runtime with $RC_UNAME.
When we use the --utc or --localtime switch, also use --noadjfile if it
is available. This means hwclock will not use a drift file.
X-Gentoo-Bug: 584722
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=584722
1. remove default /bin:/sbin:/usr/bin:/usr/sbin
2. PKG_PREFIX should be defaulted to $(PREFIX)/usr
3. LOCAL_PREFIX should be defaulted to $(PREFIX)/usr/local
X-Gentoo-Bug:583634
X-Gentoo-Bug-URL:https://bugs.gentoo.org/show_bug.cgi?id=583634
These warnings were inserted in verbose only mode in OpenRC-0.13.A
Now, we are making them more visible in preparation for removing these
compatibility binaries in the future.
Traditional System V reserves runlevel 2 for multiuser with no
networking. We add support for this which is already defined in
the inittab as
l2:2:wait:/sbin/rc nonetwork
X-Gentoo-Bug: 533828
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=533828
Signed-off-by: Anthony G. Basile <blueness@gentoo.org>
In previous releases, we either treated no mount points as critical or
all of them.
Now both localmount and netmount support a critical_mounts setting. If
mount points listed in this setting fail to mount, localmount and
netmount will fail.
Before this commit, on Linux, we were always trying to mount file
systems marked with _netdev, even when the previous mount command
failed. Now, we do not run the second mount if the first fails.
X-Gentoo-Bug: 579876
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=579876
The read builtin in most shells will interpret backslash characters
as escapes, and they are lost when reading binfmt files line-by-line.
This causes magic strings containing backslashes to be mangled and
become invalid, resulting in erroneous 'invalid entry' messages.
The -r option to read disables special handling of backslashes and
keeps all lines intact.
X-Gentoo-Bug: 575114
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=575114
Netifrc is no longer part of OpenRC, so we shouldn't save its dep tree
as part of savecache.
This should have been removed when netifrc was split out. also, it
might be related to the following bug.
X-Gentoo-Bug: 563720
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=563720
The s6-svc syntax changed for wait-up, wait-ready, wait-down, and
wait-finished. This changes the s6 handling script to use the current
valid syntax.
This fixes#65.
The whitelist of environment variables we pass to service scripts
included several unnecessary variables.
The default whitelist now includes EERROR_QUIET, EINFO_QUIET,
IN_BACKGROUND and IN_HOTPLUG.
X-Gentoo-Bug: 569542
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=569542
In the past, OpenRC was a hybrid of a centralized and file-scope
license/copyright structure.
I followed the instructions from the Software Freedom Law Center [1] to
convert to a Centralized structure where possible, for easier future
maintenance.
[1] https://softwarefreedom.org/resources/2012/ManagingCopyrightInformation.html
add in parsing of fstab to determine if nfsclient should be automatically
started so that netmount can mount nfs without adding nfsclient
to the default runlevel
This fixes#71.
- gendepends.sh needs to read this directory to allow dependencies to be
overridden
- init.sh for Linux and Bsd need to read it to allow config settings
they use to be overridden.
These functions replace rc_sys so that we can detect containers and vms
separately.
Also, we copy file_regex() to rc-misc.c and open it to all operating
systems.
In src/rc/_usage.c, we were using bootlevel as the variable to hold the
return value of rc_sys.
This changes the variable name to systype because this function returns
a system type, not a runlevel.
These functions were never meant to be used outside of OpenRC, and they
were added when we thought we were going to do away with the automatic
detection of subsystems. Since the autodetection is not going away, we
can combine these functions into rc_sys.
The want dependency is similar to the use dependency. If a service
script, for example called service1, adds "want service2" to its depend
function, OpenRC will attempt to start service2, if it exists on the
system, when service1 is started.
However, service1 will start regardless of the status of
service2.
X-Gentoo-Bug: 406021
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=406021
Rename the rc_conf_override function to describe its purpose better,
drop one conditional compile by making it available everywhere, and move
the call to it after the optional rc.conf.d directory is processed.
This makes it possible to override settings in rc.conf by adding a
directory @SYSCONFDIR@/rc.conf.d and putting files in this directory.
The files will be processed in lexical order, and the last setting in
these files will be used.
This advises users to remove mtab from their runlevels if /etc/mtab is a
symlink, and it creates the symlink if /etc/mtab does not exist on a
system.
X-Gentoo-Bug: 560060
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=560060
We were starting the value we write to the cgroup setting file with
leading spaces and this was causing issues. This change makes sure that
we aren't adding leading spaces to the value.
X-Gentoo-Bug: 562354
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=562354
On Linux, the --netdev and --nonetdev switches were not working. They
were both returning false. After this change, they operate based on the
presence or abscence of the _netdev option in mount options.
The default start-stop-daemon start function expects the command
variable to be defined to point to the daemon we want to start.
If the variable is undefined, this means that there will be nothing to
start, and in this case we should complain because it is possible that
the script writer made a typo in the variable name.
All of the dependency type lists had the types_ prefix in their names;
this has been changed to deptypes_ to make them more self documenting.
Along the same lines, the setup_types function was renamed
setup_deptypes.
The following return codes are returned by mount -a:
0: all file systems mounted.
32: no file systems mounted.
64: some file systems mounted.
The localmount/netmount services should fail if all file systems that
should mount did not mount.
The tmpfiles "d" entry will create a full path and only the last dir in
the path will have its SELinux label set correctly. This patch will
restorecon the parents as well so that the selinux labels are correct.
eg, "d /run/libvirt/lxc", then "lxc" would have the correct SELinux
label but "libvirt" would not.
Signed-off-by: Jason Zaman <jason@perfinion.com>
This change does NOT implement btrfs subvol creation. Instead, it
treats 'v' the same as 'd', which is an acceptable fallback
according to the manual.
Fixes#58
When bash is used in posix mode for the shell, the ulimit command uses
a block size of 512 bytes for the -c and -f options.
X-Gentoo-Bug: 549238
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=549238
This changes the default s6 service directory to /var/svc.d, also
it changes the code to work with the individual services instead of
forcing a rescan when a service is started or stopped.
The original way of doing this allowed users to change the supervisor in
conf.d/*. This changes this so that the supervisor setup can be done in
the service script itself.
If a service has the same name as the runlevel it is in, openrc will
crash on changing to such runlevel. It goes in a recursive madness and
eventually gets a SEGV while in snprintf (don't know why).
This fixes two errors:
1. ls_dir stats files not with full path -> stat always returns != 0
2. ls_dir adds files to list if stat failed
This fixes#53.
X-Gentoo-Bug: 537304
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=537304
This adds the -systemd-nspawn keyword to service scripts which are not
intended to run in systemd-nspawn containers.
This fixes#52.
X-Gentoo-Bug: 548058
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=548058
The dist target now creates an archive based on the version setting.
This makes it possible to create an archive identical to the ones github
generates once the release is tagged.
This changes the mtab service in the following way:
- If /etc/mtab is a symbolic link, success is returned.
- If /etc is not writable, we warn that we could not update /etc/mtab
and return success.
- If /etc/mtab does not exist, we create a symbolic link from
/etc/mtab to /proc/self/mounts.
- Otherwise, we warn that updating /etc/mtab as a file is
deprecated and continue to update it after outputting instructions to
the user for how to move it to a symbolic link.
The cache directory should be created via mkdir -p instead of
mkdir. This makes sure all parent directories are created.
Also, we now display an error message explaining that we were unable to
create the cache directory if creation fails.
We were originally checking to see if $RC_LIBEXECDIR/cache was writable. For
a new install, this check will fail since this path does not exist. This
is also incorrect because later we create $RC_LIBEXECDIR/cache.
The correct check is checkpath -W $RC_LIBEXECDIR, and this fixes the
issue.
X-Gentoo-Bug: 544632
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=544632
This makes binfmt processing behave like tmpfiles processing which
follows the same specification as systemd.
This fixes#48.
X-Gentoo-Bug: 545162
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=545162
It appears that the only reason we were force loading the usbcore
module was to facilitate mounting usbfs. Since we no longer mount
usbfs, this is no longer necessary.
X-Gentoo-Bug: 480312
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=480312
The usbfs and usbdevfs file systems have been deprecated since
Linux-2.6.32, so we remove the code to automount them.
X-Gentoo-Bug: 480312
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=480312
The selinux file system is mounted under /sys, so move the code for it
to the appropriate service.
X-Gentoo-Bug: 546290
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=546290
Tmpfiles.d processing had /run overriding /usr/lib and /etc, but this is
not correct. The correct order, from lowest to highest, for tmpfiles
processing is:
* /usr/lib/tmpfiles.d/*.conf
* /run/tmpfiles.d/*.conf
* /etc/tmpfiles.d
This means /run/tmpfiles.d/*.conf can override /etc/tmpfiles.d/*.conf,
but /etc/tmpfiles.d/*.conf can override both of them.
This fixes#49.
The local service should use eval when it executes scripts since it has
the redirection set up in a variable.
This fixes#50.
X-Gentoo-Bug: 545012
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=545012
If selinux is disabled, then stub methods will be provided instead of
calling the real methods. This removes some warnings about unused
parameters which used to be covered up with #ifdef HAVE_SELINUX.
Signed-off-by: Jason Zaman <jason@perfinion.com>
The previous fix to --test (PR #34) prevented reading one too many
arguments when --exec -or --name was not specified, but created a
regression where the last argument would not print if either of those
arguments was specified. This corrects the issue.
Fixes#41.
checkpath -W can fail if the specified path doesn't actually exist yet.
In this case savecache script should attempt to create the path if it is
missing, however it is pre-empted by the checkpath call. This patch adds
an explicit existence test before executing checkpath.
This fixes#36.
If /tmp or / are read-only, the clean_run function can fail in some very
bad ways.
1. dir=$(mktemp -d) returns an EMPTY string on error.
2. "mount -o bind / $dir", and don't check the result of that,
3. "rm -rf $dir/run/*", which removes the REAL /run contents
4. box gets very weird from this point forward
Signed-Off-By: Robin H. Johnson <robbat2@gentoo.org>
Signed-Off-By: Chip Parker <infowolfe@gmail.com>
Reported-by: Chip Parker <infowolfe@gmail.com>
Tested-by: Chip Parker <infowolfe@gmail.com>
This is another security fix. If you use chown() or chmod() on a
symbolic link, it affects the referenced file, not the symbolic link
itself.
X-Gentoo-Bug: 540006
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=540006
The local service now redirects stdout and stderr for the scripts it
runs to /dev/null unless it is run in verbose mode.
X-Gentoo-Bug: 537444
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=537444
Do not change permissions on the target if it is a file and has multiple
hard links. This is necessary because a hard link can be an attack
vector to gain privilege escalation.
X-Gentoo-Bug: 540006
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=540006
sysfs now mounts all related sysfs file systems and returns success,
like netmount and localmount.
Also, we now check to make sure the cgroups are not mounted before we
mount them.
X-Gentoo-Bug: 530138
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=530138
runscript used to dlopen() runscript_selinux.so. This adds equivalent
functionality directly in to runscript instead. It authenticates with
either PAM or shadow and optionally has a dep on audit.
X-Gentoo-Bug: 517450
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=517450
Fixes#25
Note from William Hubbs:
The original patch overwrote CFLAGS. I modified this patch to add the
ncurses cflags to CPPFLAGS instead of overwriting CFLAGS.
Check for __FreeBSD_kernel instead of __GLIBC__ in source files.
note from William Hubbs:
I was told this is a better check for GNU/kFreeBSD than checking the
C library the source is being compiled against.
GNU/kFreeBSD than checking which library we are using.
This adds support for a chroot variable which will be passed to the
start-stop-daemon --chroot switch to runscript.sh when starting a
daemon. This also needs to be saved so it can be used in locating the
pid file when stopping the daemon.
X-Gentoo-Bug: 524388
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=524388
Fix gentoo bug #427996 correctly.
We should attempt to mount the file systems, but not try to start the
daemons. The previous fix removed mounting the file systems as well as
starting the daemons.
X-Gentoo-Bug: 508574
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=508574
Note from William Hubbs:
I spoke with Roy about this, and he pointed out that user-defined
functions may need the limits applied, so it is better to go with a
method that uses exceptions to determine which functions apply the
limits.
X-Gentoo-Bug: 522408
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=522408
Originally, we aborted all of the cgroup setup if /sys/fs/cgroup/openrc
was already mounted. This caused an issue in lxc containers, so we
should always allow the subsystems to be mounted.
X-Gentoo-Bug: 520606
X-Gentoo-Bug-URL: https://bugs.gentoo.org/show_bug.cgi?id=520606
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
